2wire 2701HG-G Modem Setup - TekSavvy Community
<main> <article class="userContent"> <h2 data-id="2wire-firmware-setup">2Wire Firmware Setup</h2><h3 data-id="if-the-modem-says-2wire-in-the-top-left-corner-follow-this-guide."><strong>If the modem says 2Wire in the top left corner, follow this guide.</strong></h3><ol><li>Open a web browser and go to the address <a href="http://192.168.2.1" rel="nofollow noreferrer ugc">http://192.168.2.1</a>.</li><li>Click on the <strong>Broadband Link</strong> tab.</li><li>Under the <strong>Broadband Network</strong> section, make sure the Connection Type is PPPoE.</li><li>Enter your DSL <strong>username</strong> and DSL <strong>password</strong> (confirm password as well).</li><li>Click on <strong>Save</strong>.</li></ol><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6032279/uploads/XHSZLVFL80JY/image.png" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6032279/uploads/XHSZLVFL80JY/image.png" alt="image.png"/> </a> </div> </div> <h2 data-id="bell-firmware-setup">Bell Firmware Setup</h2><h3 data-id="if-the-modem-says-bell-in-the-top-left-corner-follow-this-guide."><strong>If the modem says Bell in the top left corner, follow this guide.</strong></h3><ol><li>Open a web browser and go to the address <a href="http://192.168.2.1" rel="nofollow noreferrer ugc">http://192.168.2.1</a>.</li><li>Click on the <strong>Settings</strong> tab.</li><li>Under the <strong>Internet</strong> section, click on <strong>Link Configuration</strong>.</li><li>Enter your DSL <strong>username (User ID)</strong> and DSL <strong>password</strong> (confirm password as well).</li><li>Click on <strong>Save</strong>.</li><li>For wireless, click on the <strong>LAN</strong> section and then click on <strong>Wireless</strong>.</li><li>Make sure <strong>Enable Wireless Interface</strong> is checked.</li><li>Enter the Network Name (SSID). SSID broadcast should be <strong>enabled</strong>.</li><li>Wireless security should be <strong>enabled</strong>.</li><li><strong>Authentication type</strong> should be set to <strong>WPA2-PSK</strong>.</li><li>Use the default encryption key as shown OR create your own.</li><li><strong>Save</strong> settings.</li></ol><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6032279/uploads/LY5AH4LDWASP/image.png" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6032279/uploads/LY5AH4LDWASP/image.png" alt="image.png"/> </a> </div> </div> <div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6032279/uploads/2C3YE8MSS2GF/image.png" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6032279/uploads/2C3YE8MSS2GF/image.png" alt="image.png"/> </a> </div> </div> <p><br></p> </article> </main>