DSL Internet : SpeedTouch Setup - TekSavvy Community
<main> <article class="userContent"> <h2 data-id="speedtouch-516">SpeedTouch 516</h2><h3 data-id="routed-setup">Routed Setup</h3><p>Routed mode should be used when you want to connect a device directly to the modem, or you are unable to configure your own stand-alone router.</p><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>SpeedTouch</strong> button. <em>(Left hand side of page.)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Routed</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region. (<em>bDSL=0.35, tDSL=0.33, eDSL may vary</em>)</li><li>Set the <strong>Connection Type</strong> to <strong>PPP over Ethernet (PPPoE)</strong>.</li><li>Click <strong>Next</strong>.</li><li>Enter the DSL username into the <strong>User Name</strong> field.</li><li>Enter the DSL password into the <strong>Password</strong> and <strong>Confirm Password</strong> fields.</li><li>Click <strong>Next</strong>.</li><li>Enter the desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is.)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><h3 data-id="bridged-setup">Bridged Setup</h3><p>Bridged mode should be used when you want to use your own third-party modem, or when troubleshooting issues not related to signal levels.</p><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>SpeedTouch</strong> button. <em>(Left-hand side of the page.)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Bridge</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region then click <strong>Next</strong>.</li><li>Uncheck (or check) the <strong>DHCP Server</strong> box, then click <strong>Next</strong>.<ul><li><strong>Check</strong> if you intend to connect a PC straight to the modem.</li><li><strong>Uncheck</strong> if you intend to use a router.</li></ul></li><li>Enter your desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is.)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><h2 data-id="speedtouch-546">SpeedTouch 546</h2><h3 data-id="routed-setup-1">Routed Setup</h3><p>Routed mode should be used when you want to connect a device directly to the modem, or you are unable to configure your own stand-alone router.</p><h4 data-id="instructions">Instructions</h4><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>SpeedTouch</strong> button. <em>(Left-hand side of the page.)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Routed</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region.</li><li>Set the <strong>Connection Type</strong> to <strong>PPP over Ethernet (PPPoE)</strong>.</li><li>Click <strong>Next</strong>.</li><li>Enter your DSL username into the <strong>User Name</strong> field.</li><li>Enter your DSL password into the <strong>Password</strong> and <strong>Confirm Password</strong> fields.</li><li>Click <strong>Next</strong>.</li><li>Enter your desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is.)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><h3 data-id="bridged-setup-1">Bridged Setup</h3><p>Bridged mode should be used when you want to use your own third-party modem, or when troubleshooting issues not related to signal levels.</p><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>SpeedTouch</strong> button. <em>(Left-hand side of the page.)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Bridge</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region then click <strong>Next</strong>.</li><li>Uncheck (or check) the <strong>DHCP Server</strong> box, then click <strong>Next</strong>.<ul><li><strong>Check</strong> if you intend to connect a PC straight to the modem.</li><li><strong>Uncheck</strong> if you intend to use a Router.</li></ul></li><li>Enter your desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><h2 data-id="speedtouch-585">SpeedTouch 585</h2><h3 data-id="routed-setup-2">Routed Setup</h3><p>Routed mode should be used when you want to use the full functionality of the modem <em>(4 ports, wireless)</em>.</p><h4 data-id="instructions-1">Instructions</h4><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>Thompson Gateway</strong> button. <em>(Left-hand side of the page)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Routed PPP</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region.</li><li>Set the <strong>Connection Type</strong> to <strong>PPP over Ethernet (PPPoE)</strong>.</li><li>Click <strong>Next</strong>.</li><li>Enter your DSL username into the <strong>User Name</strong> field.</li><li>Enter your DSL password into the <strong>Password</strong> and <strong>Confirm Password</strong> fields.</li><li>Click <strong>Next</strong>.</li><li>Enter your desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><h3 data-id="bridged-setup-2">Bridged Setup</h3><p>Bridged mode should be used when you want to use your own third-party modem, or when troubleshooting issues not related to signal levels.</p><h4 data-id="instructions-2">Instructions</h4><ol><li>Navigate to the modem's web interface. <em>(</em><a href="https://community.teksavvy.com/home/leaving?allowTrusted=1&target=http%3A%2F%2F192.168.1.254" rel="nofollow noreferrer ugc"><em>http://192.168.1.254</em></a><em>)</em></li><li>Click on the <strong>Thompson Gateway</strong> button. <em>(Left-hand side of the page)</em></li><li>Click the <strong>Set Up</strong> link. <em>(Found below </em><strong><em>Pick a task...</em></strong><em>)</em></li><li>Click <strong>Next</strong>.</li><li>Select <strong>Bridge</strong> then click <strong>Next</strong>.</li><li>Set the <strong>VPI/VCI</strong> to the correct value for your region.</li><li>Click <strong>Next</strong>.</li><li>Uncheck (or check) the <strong>DHCP Server</strong> box, then click <strong>Next</strong>.<ul><li><strong>Check</strong> if you intend to connect a PC straight to the modem.</li><li><strong>Uncheck</strong> if you intend to use a router.</li></ul></li><li>Enter your desired administrative password settings then click <strong>Next</strong>. <em>(It is highly recommended to leave this as is)</em></li><li>Click <strong>Start</strong>. <em>(The configuration process could take up to a minute)</em></li><li>Click <strong>Finish</strong>.</li></ol><p><br></p> </article> </main>